Dit is eenorigineelTerava Jaakaripuukko 110 Carbon Steel mes met schede. Het mes is gebruikt en de schede is in nieuwstaat.
De totale lengte van het mes is 23,5cm en de lengte van het lemmet is 11 x 2,5cm.
Je ontvangt exact degene van de foto's.
The Jääkäripuukko is simply a proper no-nonsense utility knife. Jääkäripuukko 110 is an excellent all-round knife for just about any tasks. Quality carbon steel, traditional Finnish puukko blade profile with a slight drop point. The Jääkäripuukko is not designed to sit on a shelf for decoration, this is an honest tool made for hard work.
General features
- Medium size general purpose utility knife, a solid choice for most situations.
- Traditional puukko-style blade profile with drop point.
- High scandi-style grind with secondary microbevel.
- Spine ground and beveled to strike sparks from ferro rods.
- Full/stick hybrid tang with textured overmolded rubber grip.
- Protruding bare tang head with lanyard hole.
TECHNICAL SPECS
| Specs | Metric | Imperial |
|---|---|---|
| Weight (knife only) | 175 g | 6.20 oz |
| Total length | 240 mm | 9.4" |
| Blade length | 110 mm | 4.3" |
| Blade thickness | 4.20 mm | 0.17" |
| Edge angle | 23° | |
| Steel | 80CrV2, 59 HRC | |
Blade
Traditional and proven functional Finnish puukko profile with a drop point. The thickness of 4,2 mm / 0.17" makes this a bit more robust than most old-timey traditional Finnish puukkos. The profile is a Scandi grind with a tiny secondary bevel, currently the most commonly used style in Finnish puukkos.
The strong blade can take a beating, you can use the Jääkäri for batoning without a problem, just don´t hit your fingers, unless yours are strong like steel.
80CRV2 CARBON STEEL AND HEAT TREATMENT
All Terävä carbon steel knives are made from 80CrV2 tool steel, a trusted choice in Finnish knife manufacturing for decades. The heat treatment leaves the surface of the steel softer, ~52 HRC. This creates a tough exterior to protect the blade. As the blade is ground, the harder (~59 HRC) inside is revealed and improves edge retention. The spine has ground bevels for striking Ferro rods.
The blades have blemishes and stains due to the manufacturing process. These are harmless and can be removed if they bother you.
CARE OF A CARBON STEEL BLADE
Carbon steel is easy to sharpen and maintain - you just have to remember to do it. If your knife gets wet in the bush, dry it the best you can. Never store the knife without drying and oiling the blade. Cooking oils are fine for this purpose.
Grip
The rubber grip is somewhat ergonomically shaped, but not one of those crazy finger groove things. A small finger guard on the front, a little belly in the middle, and a knob at the back to keep your hand from slipping and also make it possible to use a Leuku style chopping grip.
The tang runs all the way through the grip and comes out the back, forming a little knob with a hole in it for lanyards and such. The knob can also be used to hit things, naturally.
Choose the right sheath for you
The Terävä Jääkäripuukko can be carried on the belt, on a vest, or whichever way you may need. The materials are traditional leather and modern Boltaron.
LEATHER SHEATH
The sturdy leather sheath hangs on a 6 cm / 2.35" belt loop and is built with a roomy plastic liner to let water and crud to run through it and out the hole at the end. When drawing the knife, the edge runs nicely between the two leather sides, not cutting it up as is a common downside of the traditional "sock" style puukko sheaths.
The sheath retains enough tension to keep the puukko in place even without closing the snap fastener, so around camp, you don´t need to be opening and closing the sheath all the time, just remember to snap it shut when you're on the move!
Do not force the knife out of the sheath without opening the press stud!Although this can be done it is not good for the press stud in the long run and may damage it. Just open the snap before pulling out the knife. It's best to oil the snap fastener once in a while to prevent it from becoming stiff and nasty.
The words "Right" and "Left" in the menu might confuse some folks, so let’s clarify it a bit. It refers to your dominant hand, not the side of your body. You pull your knife out of the "Right" sheath with your right hand (normal grip), no matter where the sheath is – left side, right side, or on the front. The "Left" sheath goes vice versa.
If, for some reason, you prefer to pull your knife e.g. with your right hand from the right side with your knuckles between your body and the knife handle, only then take the "Left" sheath so the blade edge will be facing forward. Simple!
BOLTARON SHEATH
Boltaron is a bit like Kydex but offers better performance in the extreme ends of use temperatures. This sheath allows carrying the knife on your belt, on the vest, pack, or anything with PALS webbing.
Suitable for RH and LH users and apart from military applications, these also work in outdoor and everyday use.
